reachable time ipv6
跳到 Configuring Neighbor Reachable Time - To configure the amount of time that a remote IPv6 node is considered reachable after a reachability ... ,hosts is 5 seconds. To configure this time interval, use the ipv6 nd sync-interval .... time, use the ipv6 nd reachable-time command in interface VLAN or interface.
相關軟體 Wireshark 資訊 | |
---|---|
Wireshark 是世界上最先進的 Windows 和 Unix 免費網絡協議分析儀,也是許多行業和教育機構的事實上(通常是法律上)的標準。 Wireshark 是由全世界的網絡專家撰寫的,是開源的力量的一個例子。通過它,專業用戶可以完全分析他們的網絡連接,查看捕獲數據的詳細分類,過濾它可以更容易地識別您想要仔細檢查的流程,使用插件分析數據,創建處理數據的腳本,捕獲 VoIP 呼叫或 USB&n... Wireshark 軟體介紹
reachable time ipv6 相關參考資料
Cisco IOS IPv6 Command Reference - IPv6 Commands: ipv6 ...
To configure the length of time before an IPv6 neighbor discovery (ND) cache ...... The following example configures an IPv6 reachable time of ... https://www.cisco.com Configuring IPv6 Neighbor Discovery - Cisco
跳到 Configuring Neighbor Reachable Time - To configure the amount of time that a remote IPv6 node is considered reachable after a reachability ... https://www.cisco.com Configuring Neighbor Discovery - Cisco
hosts is 5 seconds. To configure this time interval, use the ipv6 nd sync-interval .... time, use the ipv6 nd reachable-time command in interface VLAN or interface. https://www.cisco.com IPv6 Deployment Guide
To configure the “router lifetime” value in IPv6 router advertisements on an interface, use ... Router (config-if)# ipv6 nd reachable-time milliseconds As a default 0 ... https://books.google.com.tw ipv6 nd reachable-time - Ruckus Knowledge Base
The router advertisement messages sent by a router interface include the amount of time specified by the ipv6 nd reachable-time command so that nodes on a ... http://docs.ruckuswireless.com Neighbor Discovery (ND) 簡介- IPv6 通訊協定
IPv6 Neighbor Discovery(簡稱ND)提供機制來解決鄰近nodes間相互 ..... Reachable Time 此時間的單位為毫秒,它代表當某個node被確認為可達 ... http://hanteye01.blog.fc2.com Q & A: What are the state transitions for ND6 Entries?
IPv6 Neighbor discovery state changes before going into reachable state. ... The command ipv6 nd reachable-time milliseconds may be used to modify the ... https://gtacknowledge.extremen reachable-time (IPv6 Router Advertisement) - Technical ...
Configure the value of the reachable time field of IPv6 router advertisement messages. This is the time (in milliseconds) after which a node ... https://www.juniper.net reachable-time - TechLibrary - Juniper Networks
CLI Statement. SRX Series,M Series,T Series,MX Series,PTX Series. Set the length of time that a node considers a neighbor reachable until another reachability ... https://www.juniper.net RFC 4861 - Neighbor Discovery for IP version 6 (IPv6)
RFC 4861 Neighbor Discovery in IPv6 September 2007 Table of Contents 1. ...... Reachable Time 32-bit unsigned integer. The time, in milliseconds, that a node ... https://tools.ietf.org |