extreme show lacp
The following procedure creates a dynamic LAG using LACP to use two ports, 14 and 15 on a 220-Series switch (Extreme 220) #configure (Extreme 220) ... ,How to configure and enable LLDP on EXOS-based Extreme Switches ... How to Configure Dynamic LAGs with LACP on Securestack or Chassis based switches ... switch(su)->show port status lag.0.1 Alias Oper Admin Speed Port (truncated) ...
相關軟體 GNS3 資訊 | |
---|---|
GNS3 是一種模擬複雜網絡的軟件,盡可能接近真實網絡的執行方式,所有這些都沒有專用的網絡硬件,如路由器和交換機。它還可以用來實驗功能或檢查需要在實際設備上稍後部署的配置.在無風險的虛擬環境中構建,設計和測試您的網絡,並訪問最大的網絡社區來提供幫助。無論您正在學習第一次網絡考試還是建立全州電信網絡,GNS3 都可以輕鬆設計和構建任何規模的網絡,而無需硬件。而最好的部分是免費的!為什麼要使用 GNS... GNS3 軟體介紹
extreme show lacp 相關參考資料
How to configure ActiveStandby port or LAG feature in EXOS
How to configure MLAG in Extreme switches ... Slot-1 Stack.9 # show sharing Load Sharing Monitor Config Current Agg Min Ld Share Ld Share Agg Link Link Up Master ... 1:1 1:1 LACP 1 L3 1:1 Y A ... https://gtacknowledge.extremen How to configure Dynamic LAG using LACP on 200 ... - How To
The following procedure creates a dynamic LAG using LACP to use two ports, 14 and 15 on a 220-Series switch (Extreme 220) #configure (Extreme 220) ... https://gtacknowledge.extremen How to Configure Dynamic LAGs with LACP on ... - How To
How to configure and enable LLDP on EXOS-based Extreme Switches ... How to Configure Dynamic LAGs with LACP on Securestack or Chassis based switches ... switch(su)->show port status lag.0.1 Alias O... https://gtacknowledge.extremen How To Configure LACP Over MLT - How To
Below are the steps to configure LACP over MLT on VSP 4000/7200/8000 and ERS 8000: NOTE: It is advised ... Type show mlt (verify the members are gone) 3. https://gtacknowledge.extremen How To Configure LACP with SMLT - How To
Step 2: Create MLT, enter MLT interface to add and enable LACP 1. Type mlt ... Type lacp smlt-sys-id [base mac of one of the vIST switches. ... Type show lacp https://gtacknowledge.extremen How to configure sharing (LAG) with LACP in Summit ... - How To
How to configure sharing (LAG) with LACP in Summit stack or BlackDiamond ... show lacp counters LACP PDUs dropped on non-LACP ports : 0 LACP Bulk ... Related Hub Thread: https://community.extremenetwo... https://gtacknowledge.extremen How to create or delete a share group (LAG) in EXOS - How To
How to configure MLAG in Extreme switches ... The following syntax is used to create a LAG with LACP and other settings such as ... Switch.4 # show sharing https://gtacknowledge.extremen LACP - Extreme Summit X430 and HP Procuve 2610 - 喬家大院
Extreme: #show lacp. LACP Up : Yes. LACP Enabled : Yes. System MAC : 00:04:96:xx:xx:xx. LACP PDUs dropped on non-LACP ports : 1500. http://chyau317.blogspot.com 《分享》Extreme Summit Switch的基本設定 - Shunze 學園
若檢視LACP相關資訊,則可下以下指令。 #show lacp. Click here to open new window for full size. 其中Actor指的是Extreme Switch自己,Partner指 ... http://www.shunze.info |